
Dishwasher · All brands
Dishwasher Repair in Washington, DC
Dishwasher repair in your home, condo or rental anywhere in DC, for every major brand. Same-day visits when the schedule allows.
Or book online and we'll get back to you to set a visit window.
Schedule Your Repair
Four quick steps. We'll confirm a visit window with you, and you'll get a written estimate before any work starts.
Service Type
What type of service do you need?
Or call us directly:
(703) 956-1511Repair Planned Around How Homes Here Are Built
WDC ProFix Repair fixes dishwashers in rowhouses, apartments and detached homes in all four quadrants of the District. The technician tracks down the fault where the appliance stands, writes up the repair and the price for your approval, and finishes on the spot when the part is on hand. We work on Samsung, LG, Whirlpool, GE, Maytag, Bosch and the other brands listed below. We're an independent repair company, so if your dishwasher is still under the manufacturer's warranty, contact the manufacturer first. Repairs carry a 90-day parts and 30-day labor warranty.
How It Works
Washington, DC · Arlington · Alexandria
Ready to schedule your repair?
WDC ProFix Repair: independent, in-home appliance repair with a written estimate before any work starts.
One Cycle, Several Small Machines Taking Turns
A dishwasher looks like a single box, but a cycle is really a relay between parts. The inlet valve opens and lets a measured amount of water into the tub. A circulation pump pushes that water up through the spray arms, where small jets knock food loose. A heater or the incoming hot water brings the wash to temperature, the detergent cup pops open on schedule, and a drain pump sends the dirty water out through a hose to the sink drain or disposer. Then the whole thing repeats for the rinse.
A control board runs the sequence, and it depends on feedback. A float or pressure sensor tells it the fill is complete. A thermistor reports water temperature. A door latch switch confirms the door is shut before anything moves. When one of those signals goes missing, many machines stop and flash a code rather than guess, which is why a dishwasher can seem dead when only one small switch has failed.
Reading the Symptoms Without Jumping to Conclusions
Water left standing in the bottom after a cycle usually points to the drain side. The filter may be packed with debris, the drain hose may be kinked behind the cabinet, the disposer knockout plug may never have been removed after an install, or the drain pump itself may be jammed or worn out. Any one of these can produce the same puddle.
Dishes that come out gritty or filmed have several possible causes. Clogged spray arm holes, a weak circulation pump, a fill that runs short because the inlet screen is choked, or wash water that never gets hot enough can all leave the same result. A leak at the front often traces to a worn door gasket or to suds from the wrong detergent, while a leak underneath may come from a pump seal, a loose hose clamp or a cracked tub.
If nothing happens when you press start, look first at the breaker, then suspect the latch, a thermal fuse or the board. If it starts but stalls partway through, the board may be waiting on a signal it never receives, such as a full-fill reading or a temperature it cannot reach.
Noise is its own category. A grinding or rattling sound during the wash often means a piece of glass, a bone or a fruit pit has slipped into the pump housing. A loud hum with no water moving can mean a seized pump motor. Squealing at the start of a cycle sometimes comes from a dry seal on a machine that sat unused for weeks, and it may settle down once the machine is back in regular use. A burning smell is different: stop the cycle, cut the power and leave it off until it has been checked.
How the Technician Works Through It
The visit starts with the history: what the machine did, when it started, and whether any error code has appeared. Many dishwashers have a hidden test mode that runs each part on command, so the technician will often enter it first and watch the fill, wash, heat and drain stages one at a time.
From there the checks narrow. The technician pulls and inspects the filter and sump, then measures what the inlet valve is actually delivering. Next come the pumps, listening for hum without movement and checking for resistance on the motor windings. The heater and thermistor get a meter reading, and the door latch and its switches get checked for continuity. The control board is tested last, because it is the part most often blamed and least often at fault. Once the cause is clear, you get the estimate in writing and decide whether to go ahead.
Checks You Can Safely Make First
Turn the power off at the breaker or unplug the unit before reaching into the sump. Then twist the filter cylinder out of the sump and hold it under running water. Lift off the lower spray arm, hold it up to a window to spot plugged jets, and poke those open with a toothpick.
Look under the sink to see whether the drain hose loops up high before it connects; that loop keeps sink water from siphoning back. Make sure the hot water valve under the sink is fully open. Let the sink faucet run hot for a bit before you press start. If the door does not feel like it clicks firmly shut, a latch problem is likely, and it is worth reporting when you book. Avoid pulling the machine out of the cabinet yourself, since the water line, drain and wiring all come with it.
Potomac Water, Scale and the Old Rowhouse Kitchen
The District's water starts in the Potomac, goes through the Washington Aqueduct's treatment plants, and arrives moderately hard. That does not ruin a dishwasher quickly, but over the years minerals settle where water sits or gets heated. The tiny holes in spray arms narrow, the screen at the inlet valve slowly closes up, and a crust forms on exposed heating elements. The results show up as cloudy glasses, a longer cycle and a heater that strains to reach temperature. Rinse aid and a periodic cleaning cycle with a descaling product slow that buildup down.
Many dishwashers in the District were never part of the original kitchen. In Capitol Hill rows, porch-front houses in Petworth and Bloomingdale, and rowhouses split into condos, a machine was often fitted into a cabinet run that was built decades before anyone planned for one. That can mean a drain line run a long way to a sink across the room, a supply tee shared with the faucet, or a unit squeezed in without a proper high loop or anchor brackets. Those setups work, but they make drain trouble and rocking doors more likely, and the technician will look at the installation as well as the machine.
Storms and short outages are another factor. A summer thunderstorm that flickers the power while a cycle is running can leave the control confused or knock out a board. If the dishwasher acts strangely after an outage, cut the breaker for a minute before calling, since a reset sometimes clears it.
Fix It or Replace It
Most dishwasher faults are single parts: a pump, a valve, a latch, a heater or a sensor. On a machine that is otherwise sound, replacing that part generally makes sense. The tub is the real dividing line. A cracked or rusted-through tub cannot be repaired, and if water has been leaking under the cabinet for a long time, the floor damage may matter more than the appliance.
How old it is, how many repairs it has had and whether the manufacturer still supplies parts all factor in. The technician can tell you what failed and what the rest of the machine looks like, so the choice is yours to make with real information.
Habits That Keep It Running
Scrape plates, but skip the full prewash; modern detergents need some food soil to work against. Clean the filter every few weeks, more often if your household cooks a lot. Use dishwasher detergent only, never dish soap, and keep the rinse aid dispenser full. Run the disposer before starting a cycle if the dishwasher drains into it. Once a month, run an empty hot cycle with a cleaner made for dishwashers. Before you leave town for a long stretch, it is reasonable to close the supply valve under the sink.
Renters, Condos and Building Rules
If you rent and the dishwasher came with the unit, the landlord or property manager is generally responsible for keeping it working, so contact them first. In condo and co-op buildings, check what management requires of outside vendors before the visit, such as sign-in, service elevator booking or advance notice. Water dripping into a neighbor's ceiling quickly becomes the building's problem as well as yours, so close the supply valve and tell management right away.
Still have questions?
Call or book online and ask us directly. We'll give you a straight answer.