Call Now

Washer · All brands

Washer Repair in Washington, DC

Washer repair in your home, condo or rental anywhere in DC, for every major brand. Same-day visits when the schedule allows.

Written estimate before work90-day parts & 30-day labor warrantySame-day when the schedule allowsIndependent, all major brands
(703) 956-1511

Or book online and we'll get back to you to set a visit window.

Schedule Your Repair

Four quick steps. We'll confirm a visit window with you, and you'll get a written estimate before any work starts.

1
2
3
4

Service Type

What type of service do you need?

Or call us directly:

(703) 956-1511
Written
Estimate Before Work
90-Day
Parts Warranty

Washer Brands We Repair

Samsung appliance repairLG appliance repairWhirlpool appliance repairGE appliance repairMaytag appliance repairBosch appliance repairFrigidaire appliance repairKenmore appliance repairAmana appliance repairElectrolux appliance repairMiele appliance repairAdmiral appliance repairAsko appliance repairAvanti appliance repairBlomberg appliance repairFisher & Paykel appliance repairHotpoint appliance repairRoper appliance repairSpeed Queen appliance repair
Independent Local Repair

Repair Planned Around How Homes Here Are Built

WDC ProFix Repair fixes washers in rowhouses, apartments and detached homes in all four quadrants of the District. The technician tracks down the fault where the appliance stands, writes up the repair and the price for your approval, and finishes on the spot when the part is on hand. We work on Samsung, LG, Whirlpool, GE, Maytag, Bosch and the other brands listed below. We're an independent repair company, so if your washer is still under the manufacturer's warranty, contact the manufacturer first. Repairs carry a 90-day parts and 30-day labor warranty.

Rowhouses & Conversions
Victorian rows with basement laundry, English-basement units, and condo conversions with closet washers upstairs.
Co-ops, Condos & Rentals
We work within service-elevator bookings, board rules and tenant access, and leave written notes for whoever pays.
Arrival Windows We Keep
You get a three-hour window we can actually make across DC traffic. A same-day slot is offered only when one is open.
Brands in DC Kitchens
Builder-grade GE and Whirlpool in older rows, Bosch and Samsung in newer condos, Sub-Zero and Wolf in renovated homes.
Price in Writing
The technician tests the appliance, names the failed part and puts the price on paper. You decide before any work begins.
Parts & Labor Covered
Parts we install carry 90 days and our labor 30 days. A repeat of the same fault in that time is ours to put right.
Independent Repair Company
Not a manufacturer warranty center; in-warranty units go to the maker first
Local Conditions
Muggy summers, storm outages and moderately hard Potomac water all factor into the diagnosis
Citywide Coverage
All four DC quadrants, plus Arlington and Alexandria, VA
Worth Fixing?
When the repair costs too much for an older unit, the technician says so before you spend anything

How It Works

01
Describe the Problem
Share the appliance, the brand and what it is or isn't doing
02
Pick a Time
We agree on a three-hour arrival window that suits your building
03
Find the Fault
Testing first, then a written price you approve or decline
04
Fix and Check
The repaired unit is run through a full cycle before we go

Washington, DC · Arlington · Alexandria

Ready to schedule your repair?

WDC ProFix Repair: independent, in-home appliance repair with a written estimate before any work starts.

Fill, Agitate, Drain, Spin: The Washer's Basic Loop

Every washing machine repeats the same handful of steps. An inlet valve lets hot and cold water in until a pressure sensor or a timed fill says the level is right. A motor moves the clothes through that water, either by turning an agitator or impeller in a top-loader or by tumbling the drum in a front-loader. A pump empties the tub through the drain hose. Then the motor spins the drum fast to throw water out of the fabric, and the cycle repeats for the rinse.

Around that loop sit the parts that keep it safe and balanced: a lid or door lock that keeps the drum closed while it turns, suspension springs or shock absorbers that steady the tub, bearings that carry the drum shaft, and a control board that reads sensors and decides what happens next. Many repair calls come down to one sensor telling the board something is wrong and the board halting the cycle.

Which Washer Do You Have?

Top-load agitator washers are the traditional design, with a central post that rubs clothes against each other. They fill high, are forgiving of detergent and tend to be mechanically simple. High-efficiency top-loaders replace the central post with a low wash plate and use far less water; they rely on sensors to judge the load and can be more sensitive to imbalance.

Front-loaders tumble clothes through a shallow pool and spin very fast. They clean well with little water but depend on a sealed door boot, a door lock, a drain pump filter and heavy drum bearings. Stacked laundry centers and stackable pairs put a front-load or top-load washer under a dryer in a single frame, which saves space but makes access harder. All-in-one washer-dryers wash and then dry in the same drum, usually without an outside vent; they are popular in apartments but have longer cycles and more parts in one cabinet.

The type matters for both diagnosis and planning: a stacked unit may need to be separated before the washer can be pulled forward.

From Symptom to Suspect

Standing water after the final spin usually sends attention to the drain path. A sock in the pump filter, a kinked hose or a failed drain pump are frequent causes. A washer that will not spin but drains may have a lid or door lock fault, a worn drive belt, a failed motor control, or simply an unbalanced load that the board refuses to spin.

A roar that rises with spin speed is often worn drum bearings, especially on front-loaders. Banging during spin can be a broken suspension spring or a worn shock absorber. Slow fills tend to come from clogged inlet screens or a weak inlet valve. A musty smell or black spots in the door boot of a front-loader suggest residue and moisture trapped in the seal.

Leaks are worth tracing carefully. Water at the front of a front-loader may come from the door boot; under the machine it can be the pump, a hose clamp or the tub seal; behind it, often the fill hoses.

Owner Checks That Are Safe to Make

Unplug the washer before reaching inside or behind it. Check that both supply valves are open fully and that the fill hoses are not kinked when the machine is pushed back. If the washer fills slowly, the small screens where the hoses attach can be cleaned once the water is off and the hoses removed.

On front-loaders, a small access panel near the floor hides the pump filter, which traps coins, hair ties and lint. Put down towels and a shallow pan before opening it; a fair amount of water will come out. Redistribute a heavy, lopsided load and try a spin-only cycle. Use HE detergent in the amount the machine calls for. Too much soap can cause suds lock, poor rinsing and odors.

If the washer shows an error code, write it down before resetting anything. It helps the technician start in the right place. On a top-loader that will not spin, confirm the lid switch clicks when you close the lid; a broken strike tab on the lid is a common, simple cause. For a front-loader that will not unlock, wait a few minutes after the cycle ends, since many locks stay engaged until the water level and drum speed drop to zero.

Rowhouse Basements, Upstairs Closets and DC Water

In many District rowhouses the laundry sits in the basement, often beside the water heater and a floor drain. Where the house has an English basement rented as a separate unit, the laundry may be shared, or it may belong to one unit with shutoff valves on the other side of a locked door. It helps to know where the valves are before anything goes wrong, and a tenant whose washer came with the apartment should raise the problem with the landlord before anything else.

When a rowhouse is split into condos, the laundry usually ends up in an upper-floor closet, often as a stacked unit. A leak there lands on someone's ceiling. A drain pan with a drain line, braided steel fill hoses and an automatic water-leak sensor are inexpensive protections. Spin vibration on a wood-framed floor can also be dramatic, so level the machine carefully and do not overload it.

Basements on the combined sewer system in older neighborhoods can take on water during a heavy storm. If a washer sat in floodwater, leave it unplugged and have the motor, pump, controls and wiring checked before using it. A backwater valve on the sewer line is a fix many owners ask a plumber about.

Washington's tap water is moderately hard. Slowly, that mineral content crusts the fill-valve screens, the internal heater on models that warm their own water, and sometimes the small hose the level sensor uses. Regular cleaning cycles help, and soft scale on the screens is one reason a slow fill deserves a look.

What the Technician Tests, Step by Step

The technician starts by reading any stored fault codes and running the machine's own diagnostic mode, which many models include. Then the basics are confirmed: water supply, drain height and hose routing, and whether the machine is level. From there testing follows the failed step in the cycle.

For a drain fault, the pump filter and hose are checked, then the pump's resistance and voltage. For a spin fault, the lid or door lock, the belt or direct drive, the motor and its control are tested. A noisy spin gets a hands-on check of the drum for play that indicates bearing wear, and the suspension is inspected. You get the diagnosis in plain words and a written estimate before the repair begins.

On a stacked pair in a closet, part of the visit is simply making room to work: separating the units or sliding the stack forward carefully so hoses, the dryer duct and the floor are not damaged. Clearing the closet and the hallway in front of it beforehand saves time. If the machines are on a raised pedestal, mention that when booking.

When a Repair Makes Sense

Pumps, inlet valves, door locks, belts, lid switches, shock absorbers and many control boards are common repairs on washers with plenty of life left. Bearing replacement on a front-loader is a larger job because the tub often has to come apart, and on some models the bearings are sealed into a one-piece tub that is replaced as an assembly.

Weigh the age of the machine, its overall condition and how hard it would be to get a replacement into the space. In a closet built around a particular stacked unit, finding a new model that fits the opening and hookups can be its own project. The technician can tell you which repair is routine and which deserves a second thought.

Laundry Habits That Prevent Repeat Visits

Leave a front-loader door and dispenser drawer ajar after the last load so the boot dries. Wipe the gasket folds weekly. Run a cleaning cycle monthly. Empty pockets, use mesh bags for small items, and clean the pump filter every few months. Replace rubber fill hoses every few years, or use braided ones, and never run the washer while nobody is home if it sits above finished space.

FAQ

Washer repair: common questions

Can't find your answer? Book a service call or call us now.

Still have questions?

Call or book online and ask us directly. We'll give you a straight answer.

Washer problems we repair

Not Spinning
Not Draining
Making Loud Noise
Won't Start
Leaking Water
Not Filling with Water
Door Won't Lock
Vibrating Excessively
Error Codes Displayed
Not Agitating
Clothes Not Getting Clean
Washer Smells Bad
Mold in Drum or Gasket
Musty Odor Transferring to Clothes
Door Gasket Mold
Not Rinsing Properly
Too Much Suds / Oversudsing
Detergent Not Dispensing
Fabric Softener Not Dispensing
Bleach Dispenser Clogged
Spin Cycle Stopping Early
Not Completing Full Cycle
Cycle Taking Too Long
Pausing Mid-Cycle
Filling Too Slowly
Overfilling with Water
Standing Water After Cycle
Not Draining Completely
Grinding Noise During Wash
Banging Noise During Spin
Squealing Noise
Clicking Noise During Cycle
Burning Smell from Washer
Door Won't Open After Cycle
Door Glass Cracked or Broken
Door Seal / Gasket Torn or Damaged
Leaking from Bottom
Leaking from Door
Leaking from Back of Washer
Leaking from Detergent Drawer
Drum Not Turning
Agitator Not Working
Agitator Dogs / Cogs Worn Out
Drum Bearing Making Noise
Drive Belt Broken
Motor Failure
Drain Pump Failure
Water Inlet Valve Failure
Lid Switch / Lock Failure
Control Board Failure
Water Temperature Wrong
Washing Cold Only / No Hot Water
Clothes Getting Damaged in Washer
Tearing or Ripping Clothes
Clothes Coming Out Tangled
Soap Residue on Clothes
Fabric Softener Spots on Clothes
Rust Stains on Clothes
Washer Won't Turn On
Display / Control Panel Not Working
Buttons Not Responding
Pausing Randomly During Cycle
Tripping Circuit Breaker
Shaking the Floor During Spin
Washer Moving Across Floor During Spin
Not Balancing Load During Spin
UE / Unbalance Error (LG)
OE / Drain Error (LG)
LE / Motor Error (LG)
DE / Door Error (LG)
5E / SE Drain Error (Samsung)
F21 Drain Error (Whirlpool)
F5 / dL Lid Lock Error (Whirlpool / GE)
Drum Bearing Replacement Needed
Shock Absorbers Worn Out
Spider Arm / Drum Support Broken
Pump Filter Clogged
CallBook