Call Now

Ice Maker · All brands

Ice Maker Repair in Washington, DC

Ice Maker repair in your home, condo or rental anywhere in DC, for every major brand. Same-day visits when the schedule allows.

Written estimate before work90-day parts & 30-day labor warrantySame-day when the schedule allowsIndependent, all major brands
(703) 956-1511

Or book online and we'll get back to you to set a visit window.

Schedule Your Repair

Four quick steps. We'll confirm a visit window with you, and you'll get a written estimate before any work starts.

1
2
3
4

Service Type

What type of service do you need?

Or call us directly:

(703) 956-1511
Written
Estimate Before Work
90-Day
Parts Warranty

Ice Maker Brands We Repair

Sub-Zero appliance repairAtosa appliance repairHoshizaki appliance repairTraulsen appliance repairManitowoc appliance repairMaxxIce appliance repairPerlick appliance repairScotsman appliance repairU-Line appliance repair
Independent Local Repair

Repair Planned Around How Homes Here Are Built

WDC ProFix Repair fixes ice makers in rowhouses, apartments and detached homes in all four quadrants of the District. The technician tracks down the fault where the appliance stands, writes up the repair and the price for your approval, and finishes on the spot when the part is on hand. We work on Sub-Zero, Atosa, Hoshizaki, Traulsen, Manitowoc, MaxxIce and the other brands listed below. We're an independent repair company, so if your ice maker is still under the manufacturer's warranty, contact the manufacturer first. Repairs carry a 90-day parts and 30-day labor warranty.

Rowhouses & Conversions
Victorian rows with basement laundry, English-basement units, and condo conversions with closet washers upstairs.
Co-ops, Condos & Rentals
We work within service-elevator bookings, board rules and tenant access, and leave written notes for whoever pays.
Arrival Windows We Keep
You get a three-hour window we can actually make across DC traffic. A same-day slot is offered only when one is open.
Brands in DC Kitchens
Builder-grade GE and Whirlpool in older rows, Bosch and Samsung in newer condos, Sub-Zero and Wolf in renovated homes.
Price in Writing
The technician tests the appliance, names the failed part and puts the price on paper. You decide before any work begins.
Parts & Labor Covered
Parts we install carry 90 days and our labor 30 days. A repeat of the same fault in that time is ours to put right.
Independent Repair Company
Not a manufacturer warranty center; in-warranty units go to the maker first
Local Conditions
Muggy summers, storm outages and moderately hard Potomac water all factor into the diagnosis
Citywide Coverage
All four DC quadrants, plus Arlington and Alexandria, VA
Worth Fixing?
When the repair costs too much for an older unit, the technician says so before you spend anything

How It Works

01
Describe the Problem
Share the appliance, the brand and what it is or isn't doing
02
Pick a Time
We agree on a three-hour arrival window that suits your building
03
Find the Fault
Testing first, then a written price you approve or decline
04
Fix and Check
The repaired unit is run through a full cycle before we go

Washington, DC · Arlington · Alexandria

Ready to schedule your repair?

WDC ProFix Repair: independent, in-home appliance repair with a written estimate before any work starts.

Three Kinds of Ice Makers, Three Different Machines

"Ice maker" covers very different equipment. The most common is the module mounted in a refrigerator's freezer or in the door of a French-door model. It borrows cold from the fridge and adds only a fill valve, a mold, a heater and a small motor. The second is the undercounter clear-ice machine, a self-contained appliance with its own compressor that freezes water in layers on a cold plate or grid. The third is the countertop or nugget machine that freezes water inside a chilled cylinder and scrapes it off as soft, chewable pellets.

This guide is about making ice. If your refrigerator is warm or the freezer will not hold temperature, the ice maker is only a casualty; the refrigerator or freezer guide is the better place to start.

How a Refrigerator Ice Module Fills, Freezes and Harvests

When the mold is empty and cold enough, the module energizes the fill valve mounted on the cabinet's rear for a few seconds. Water runs up a small line, through the fill tube into the mold, and freezes. A thermostat or sensor on the mold decides when the cubes are solid. A small heater then loosens them, and an ejector arm or a twisting tray pushes them into the bin. A shut-off arm or an optical sensor stops production when the bin is full.

Each step has its own failure. Little or no water reaches the mold if the valve, the filter or the supply line is restricted. A fill tube that freezes shut blocks water entirely. A failed heater or motor leaves cubes stuck in the mold. A sensor reading the bin as full keeps the module idle no matter how empty the bucket looks.

Clear-Ice and Nugget Machines Work Differently

An undercounter clear-ice machine circulates water over a chilled evaporator so it freezes in thin sheets; dissolved minerals stay in the leftover water, which is flushed down the drain. That is why the ice is clear. It also means these machines depend on a drain: a gravity line or a built-in pump that lifts water to the sink drain. A blocked drain, a failing pump or a scaled evaporator are common service calls. Many also have a condenser that needs regular cleaning, just like a refrigerator.

Nugget machines use an auger turning inside a frozen cylinder. Scale on the cylinder wall makes the auger strain and the motor grind, and production slows long before the machine stops. Countertop portables are simpler still and are often sold as nearly disposable, which affects the repair decision.

Common Complaints and What Often Sits Behind Them

No ice at all: check whether the module is switched on, then whether water reaches the mold. Frequent culprits include ice plugging the fill tube, a replacement filter not locked in, a shutoff left partly closed, or a valve that no longer opens. Small, hollow or crescent-shaped cubes usually mean too little water per fill, often from low pressure, a clogged filter or a scaled valve screen.

Ice fused into a block in the bin often happens when the dispenser is seldom used or the freezer is too warm and cubes partly melt and refreeze. Water dripping onto the bin or the freezer floor can come from a leaking valve that keeps trickling, an overfill, or a cracked fill cup. Ice that tastes stale typically absorbs odors from the freezer, or reflects an old filter or a water line that needs flushing.

On a clear-ice machine, cloudy ice, slow production or a puddle under the unit are classic signs of scale or a drain problem.

What to Try Yourself, and What to Leave Alone

Confirm the ice maker switch or the control setting is on and that the bin is seated so the sensor sees it. Check that the household supply valve behind the fridge or under the sink is fully open. If you recently changed the filter, reseat it and run a few glasses through the dispenser to purge air. Look at the fill tube where it enters the mold; if it is capped with ice, a hair dryer on low held at a distance can clear it, with the fridge unplugged.

Empty a bin that has clumped and discard the old ice. Wipe the bin and let the module start fresh. On an undercounter machine, run the cleaning cycle with the descaler the manufacturer specifies and check that the drain is not kinked.

Leave the inlet valve, the module wiring and any refrigeration work alone. The valve runs on household voltage and sits close to water. Also resist the urge to force the ejector arm or pry cubes out of the mold with metal tools; the mold has a nonstick coating and an embedded heater that are easy to damage. If the module was switched off for a vacation, give it a full day after switching it back on before deciding it has failed, since the first harvest can take several hours.

Potomac Water, Spring Chlorine and Winter Supply Lines

District tap water is drawn from the Potomac, treated by the Washington Aqueduct, and lands in the moderately hard range. Over time, minerals settle on the fine screen in the water inlet valve and inside clear-ice evaporators. The result is slow fills, small cubes and clear-ice machines that need descaling more often than a manual might suggest for soft water. A quality filter helps the refrigerator module; an undercounter machine benefits from a scale-reducing filter on its own supply line.

Each spring DC Water switches its disinfectant from chloramine to free chlorine for a few weeks, and many people notice the taste in their ice. A fresh filter helps with taste. It is not a lead treatment unless certified to NSF/ANSI 53.

Older rowhouses sometimes route the refrigerator supply line along an exterior wall, across an unheated porch or through a crawl space. In a cold snap, that line can freeze. Insulating the run or relocating it is a plumbing job, but the technician can confirm whether a frozen line or the ice maker itself is at fault. Some older installations still use a saddle valve clamped onto a pipe; those tend to clog and leak, and a plumber can replace one with a proper shutoff.

Roof decks and basement bars in renovated rowhouses sometimes have an undercounter ice machine. Machines placed outdoors or in a hot space without proper ventilation struggle in August heat, and production drops.

How the Technician Narrows It Down

For a refrigerator module, the technician measures freezer temperature first, since a warm freezer will not let the module cycle. Then water supply and pressure are confirmed at the valve, the valve coils are tested, and the module is put through a forced harvest to watch the heater, motor and fill in sequence. For clear-ice machines, the order runs from water and drain to condenser cleanliness, then the pump, sensors and refrigeration side. You get a written explanation of what was found and a price before parts go on order.

Fix the Module or Replace It?

On many refrigerators the ice module is a single replaceable assembly, so the question is simply whether the module, the valve or the water supply is at fault. That is usually a straightforward repair. Undercounter clear-ice machines cost enough that repairing pumps, valves and sensors almost always makes sense; a failed compressor on an older unit deserves a harder look. Inexpensive countertop machines are often better replaced once anything beyond cleaning is needed.

One more factor is the water line itself. A cracked plastic supply tube or a corroded valve behind the fridge is a small part, but ignoring it risks a slow leak under the floor. If the line is old, replacing it during the visit is usually a sensible add-on, and it costs far less than fixing a stained ceiling in the basement apartment below.

Keeping Ice Clean and Production Steady

Change the refrigerator filter on the schedule in the manual. Use the ice regularly or empty the bin every few weeks. Descale and sanitize undercounter machines on the maker's schedule, and clean their condenser. If you will be away, turn the ice maker off so a slow valve leak cannot build ice in the freezer.

FAQ

Ice Maker repair: common questions

Can't find your answer? Book a service call or call us now.

Still have questions?

Call or book online and ask us directly. We'll give you a straight answer.

Ice Maker problems we repair

Not Making Ice
Making Small or Hollow Ice Cubes
Leaking Water
Ice Tastes or Smells Bad
Overfilling with Ice
Making Loud Noise
Producing Too Little Ice
Ice Clumping Together
Water Leaking from Ice Maker
Ice Not Dispensing
Ice Has Bad Taste or Odor
Producing Small or Hollow Ice Cubes
Ice Cubes Appear Cloudy
Ice Maker Overflowing Bin
Drain Pump Failure
Freezing Section Not Cold Enough
Condenser Dirty Reducing Efficiency
Water Inlet Valve Failure
Ice Maker Freezing Up Internally
Ice Maker Unit Won't Turn On
Ice Bin Agitator Motor Failure
Scale Buildup in Water Lines
Ice Production Drops in Summer
Ice Harvest Cycle Too Slow
Water Pump Failure
Evaporator Coil Iced Over
Ice Cubes Inconsistent Size
Water Reservoir Overflowing
Control Board Failure
Hot Gas Harvest Valve Failure
Water Distribution Tube Clogged
Not Making Cube Ice — Making Flakes Instead
Nugget Ice Maker Not Producing Nuggets
Ice Maker Tripping Circuit Breaker
Ice Maker Needs Sanitizing
Scale Buildup on Evaporator Plate
Compressor Starting Problems
Water Flowing Constantly into Ice Maker
Ice Stuck in Mold / Won't Release
Water Line Taste Affecting Ice
Outdoor Ice Maker Not Keeping Up in Summer
Nugget Ice Maker Scale Buildup
Ice Maker Smells Musty
Not Reaching Rated Ice Production
Ice Forming Outside the Bin
Ice Maker Making Loud Operation Noise
Ice Production Varies Seasonally
Water Not Circulating Over Evaporator
Slime or Mold Inside Ice Machine
Error Code on Ice Maker Display
Condensate Drain Clogged
Not Stopping When Bin Is Full
Portable Countertop Ice Maker Problems
Ice Maker Requiring Warranty Decision
CallBook