Laundry in the District lives in all sorts of places. A rowhouse that was split into condos usually has a stacked pair tucked into a hallway closet on an upper floor. In a rowhouse still lived in as one home, the pair usually sits downstairs near the water heater. A detached house in Upper Northwest might have them in the garage or a mudroom. Each spot works, but each one asks something different of the floor, the plumbing, the wiring and the exhaust.
Use this list when you are moving machines into a new spot, replacing a pair, or trying to figure out why a setup that came with the house keeps giving trouble. It is written for owners and renters alike, though renters should involve the landlord before changing anything that connects to the building.
The Floor Under the Machines
A washer in its spin cycle pushes hard against whatever holds it up. Concrete basement slabs handle that well. Wood-framed floors in older rowhouses and pop-up additions flex more, and that flex shows up as walking, banging and noise that carries into the unit below.
- Level the machine on all four feet and lock the adjusting nuts. Rock each corner by hand; any movement means it is not settled.
- Check for soft spots. Press on the subfloor around the closet with your heel. Sponginess near the drain can mean an old slow leak.
- Use a drain pan on any floor above living space. In a condo conversion, the ceiling under your closet belongs to a neighbor. A pan with a drain line, or at least a water sensor, buys time when a hose fails.
- Confirm the stacking kit. A dryer on top of a washer needs the kit the manufacturer specifies for that pair. Do not stack mismatched brands with a homemade bracket.
Water Supply and Shutoffs
Hoses fail more often than machines do, and the damage depends on how fast someone can stop the water.
- Find the two supply valves behind the machine and make sure they turn. In an English basement, the shutoff for your laundry may sit in the other unit or in a shared utility room, so learn where it is before you need it.
- Replace rubber fill hoses that are cracked, bulging or of unknown age. Braided stainless hoses are a common upgrade, though they still wear and should be inspected.
- Clean the inlet screens. DC's water is moderately hard, and the small filter screens where the hoses attach to the washer slowly collect scale and grit. Shut the valves, remove the hoses, and rinse the screens.
- Leave a little slack. Hoses pinched against the wall kink, and kinks slow the fill.
The Drain
A washer pumps water out fast. The standpipe or laundry sink it drains into has to keep up.
- Push the drain hose into the standpipe only as far as the manual recommends, and secure it so it cannot jump out during a pump-out.
- Run a full-load drain while you watch. If the standpipe overflows mid-drain, suspect a clog partway down or a pipe too narrow for the pump.
- In basements with a floor drain, keep it clear. In older parts of the city on the combined sewer, heavy storms can push water back up through low drains, so never set the machines directly over one.
Electricity and Gas
- Washer: a standard grounded outlet within reach of the cord. Skip extension cords.
- Electric dryer: a dedicated high-voltage circuit and the correct receptacle for the cord. Older homes may have a three-prong dryer outlet; a new dryer might ship expecting a four-prong cord. Match the cord to the outlet, or have an electrician update the circuit.
- Gas dryer: a proper gas supply with a shutoff valve and an approved flexible connector, plus a regular outlet for the controls. Gas connection work belongs to a qualified installer. Gas odor in the laundry area? Get people out, leave the light switches in whatever position they are in, and wait until you are outdoors to contact Washington Gas or 911.
- Garages: outlets there are often GFCI-protected. A washer that keeps tripping one may have a wiring or moisture issue worth tracking down.
Venting the Dryer
The vent is where many setups go wrong, especially in closets. A dryer needs a short, smooth path to the outdoors, and closet installs in converted rowhouses sometimes route the duct through a long run of joists to reach a rear wall.
- Use rigid or semi-rigid metal duct, not foil or vinyl.
- Route the duct as directly as you can, and compare its length and elbows with the limit printed in the dryer's installation guide.
- Make sure the exterior hood flap opens when the dryer runs and closes when it stops.
- If the closet has a door, check whether the dryer needs louvers or a gap for makeup air.
In a historic district, a new hole through a front wall may need review, so rear and side routes are usually easier. Duct materials and hood checks are covered step by step in our dryer vent safety checklist.
Garage and Unheated Basement Extras
- Water left in the washer's pump and hoses can freeze in an unheated garage. Keep the space above freezing, or follow the manual's winterizing steps.
- Raise machines on a level platform if the floor gets wet in heavy rain.
- Keep paint, gasoline and solvents well away from a gas dryer.
Building Rules for Condos and Co-ops
If you live in a condo or co-op, read the rules before adding or replacing laundry. Some buildings require drain pans, specific hoses, approved contractors or advance notice for any work. In prewar co-ops along Connecticut Avenue, in-unit laundry may not be allowed at all. Ask management what it requires from anyone coming to service the machines.
Help With the Machines Themselves
Once the space is right, the appliance still has to work. If a washer will not drain, leaks from underneath, or shakes no matter how level it is, or a dryer runs but stays cool, a technician can find the cause. WDC ProFix handles washer repair and dryer repair in closets, basements and garages across the city, including the converted rowhouses of Petworth. Book online or call us to set up a visit.
