Call Now

Refrigerator · Checklist

Before You Haul Home a Secondhand Fridge: An Inspection and Doorway Checklist

Buying a used refrigerator in DC? Check how it cools, seals and drains, look up recalls, then measure every doorway and stairwell on the way to your kitchen.

By WDC ProFix Service Team4 min read

A used refrigerator from a neighbor, an online listing or a renovation sale can be a sensible buy. It can also be someone else's problem. Most of what matters can be checked in fifteen minutes if the seller has it plugged in and running, and a few more minutes with a tape measure at home can save you from a fridge that will not get past your front door.

Ideally the fridge has been switched on and cooling for a full day when you arrive, so ask the seller to plug it in ahead of time. A fridge that has been sitting unplugged in a garage tells you very little.

Paperwork and Identity

  • Snap a photo of the rating label; look on an inner side wall of the fresh-food compartment or close to the crisper drawers. It shows the model, serial number and electrical rating.
  • Search the model on CPSC's recall listings before you pay. Our recall checklist walks through the search.
  • Ask how old it is and why it is being sold. "We remodeled" is a different story from "it kept icing up."
  • Ask for the manual, or download it using the model number.

Is It Actually Cold?

Set an appliance thermometer on a center shelf as soon as you arrive and read it once you have looked over the rest.

  • A running fresh-food section should be at or below 40°F. The freezer should be close to 0°F and solidly frozen.
  • Feel the freezer walls. Even cold is good; one warm area or a warm back wall can point to an airflow problem.
  • Thick frost across the freezer's rear panel is a bad sign, and it often traces back to the defrost system.
  • Listen. A steady hum from the compressor and the sound of a fan are normal. Loud knocking, rattling, or a compressor that clicks on and immediately off are warning signs.

Doors, Gaskets and Shelves

  • Close each door on a strip of paper at several points around the gasket. You should feel resistance when you pull it out.
  • Let each door go from half open: it should drift shut by itself, and the hinges should hold it square.
  • Count shelves, bins and door racks. Replacement parts for an older model can be hard to find.
  • Look for cracked liners, rust at the bottom of the doors and a musty smell that will not wipe away.

Water, Ice and Drains

  • Check under the crisper drawers for standing water, which usually means a blocked defrost drain.
  • If there is an ice maker or dispenser, ask whether it was hooked up. Test it if it was.
  • Ask when the water filter was replaced. Plan to replace it anyway. Worried about lead? Check the replacement cartridge's packaging for NSF/ANSI 53 lead-reduction certification; without it, the filter is for taste and odor.
  • Look at the back for the water line connection and any signs of old leaks.

An ice maker that will be connected to an older DC home's plumbing has its own considerations. Our water line checklist covers valves, tubing and where to tap in.

Think About What It Costs to Run

A low price at pickup is only part of the story. A refrigerator runs every hour of the day, so an old, inefficient unit keeps adding to each Pepco bill. If the seller still has the yellow EnergyGuide label, compare it with newer models, or look up the model's energy use online. ENERGY STAR's refrigerator guidance explains why an aging fridge kept as a year-round spare is often worth replacing.

Measure the Way In

This step is where a lot of secondhand deals fall apart in Washington. Rowhouse front doors, narrow vestibules, tight turns at the top of basement stairs and condo hallways all limit what will fit.

  1. Measure the fridge: height, width and depth, including the handles. Note whether the doors can come off.
  2. Measure every opening on the path: the front or alley door, any vestibule, hallways, the kitchen doorway, and stairwells if the kitchen is up or down a level.
  3. Check turns. A tall unit tipped onto a dolly needs clearance at landings, not just straight stretches.
  4. Measure the space it goes in, leaving room for air at the sides, top and back as the manual describes.
  5. Check building rules. Apartment and condo buildings may require a reserved service elevator, a loading dock window or a certificate from the movers. Ask management what it requires.
  6. Plan parking. Many rowhouse blocks have a rear alley that is easier than the front steps. Permit-parking streets can make a quick stop with a truck tricky.

Moving It Without Hurting It

  • Keep the fridge upright if you can. If it must lie down, ask the manufacturer's guidance on how long to let it stand before plugging it in.
  • Tape the doors shut, remove loose shelves, and protect the floor.
  • Plug it directly into a wall outlet once it is in place, not into an extension cord.
  • Give it several hours to cool before you load food.

After It Is Home

Clean the condenser coils, which are often thick with dust on a used unit. Watch the temperatures for the first week. If it struggles to stay cold, ices up, leaks or makes new noises, WDC ProFix can diagnose it in your kitchen and explain what a repair would involve before anything is replaced. Learn more about our refrigerator repair service.

Checklist Done and Still Stuck?

In-home appliance repair across Washington, DC · Written estimate before any work starts · 90-day parts & 30-day labor warranty

More From Our Blog

CallBook