
Range · All brands
Range Repair in Washington, DC
Range repair in your home, condo or rental anywhere in DC, for every major brand. Same-day visits when the schedule allows.
Or book online and we'll get back to you to set a visit window.
Schedule Your Repair
Four quick steps. We'll confirm a visit window with you, and you'll get a written estimate before any work starts.
Service Type
What type of service do you need?
Or call us directly:
(703) 956-1511Repair Planned Around How Homes Here Are Built
WDC ProFix Repair fixes ranges in rowhouses, apartments and detached homes in all four quadrants of the District. The technician tracks down the fault where the appliance stands, writes up the repair and the price for your approval, and finishes on the spot when the part is on hand. We work on Samsung, LG, Whirlpool, GE, Maytag, Bosch and the other brands listed below. We're an independent repair company, so if your range is still under the manufacturer's warranty, contact the manufacturer first. Repairs carry a 90-day parts and 30-day labor warranty.
How It Works
Washington, DC · Arlington · Alexandria
Ready to schedule your repair?
WDC ProFix Repair: independent, in-home appliance repair with a written estimate before any work starts.
A Range Is a Cooktop and an Oven Sharing One Body
A range combines surface burners and an oven in one appliance, joined by shared wiring, a shared gas manifold or both, and often a single control panel. A freestanding model has finished side panels and usually carries its knobs or keypad on a raised back panel. Slide-in ranges fit flush between cabinets with controls up front. Pro-style ranges bring heavier grates, sealed high-output burners and sometimes a griddle or two ovens side by side. A dual-fuel model puts gas burners over an electric oven.
Because so much is shared, a range repair is often about the connection between the halves. A problem with the power cord, the main gas regulator, the control board or the cooling fan can affect both the top and the oven at once, which a separate cooktop and wall oven would never do.
Faults That Show Up on a Whole Range
When both the burners and the oven quit at the same moment, the trouble is usually upstream of either one. With electric models, the usual suspects are a half-tripped double breaker, a worn power cord or scorched lugs where that cord meets the range. On a gas range, a closed shutoff valve, a failed regulator or no power to the igniters may be to blame, since even gas ranges need electricity for spark and glow ignition.
Dual-fuel ranges add a twist. The cooktop runs on gas and the oven on a 240-volt electric circuit, so the gas side can work perfectly while the oven is dead, or the reverse. A range that clicks constantly at every burner, even with the knobs off, often has moisture on a spark switch or a failed spark module. A control panel that goes blank or beeps without reason may have a damaged board or touchpad.
If the whole unit lifts or leans when someone pulls the oven door down, treat that as a safety issue, not a quirk. The bracket that anchors a rear leg to the floor or wall is probably absent or out of place, and that comes before any other work.
Dual-Fuel and Pro-Style: What Is Different
Pro-style ranges run hotter and carry more weight, so their parts are built differently. Burners may use separate spark modules for each side, ovens may have infrared broilers, and the cooling systems work harder. Some use continuous re-ignition, which relights a burner if a draft blows it out, and that system has its own sensors.
These ranges also tend to be installed in renovated kitchens with dedicated hoods and specific clearance requirements. Moving one for service is normally a two-person job, with the flooring covered first. The technician will want to know the make and model ahead of time so the right parts and tools come along.
What the Technician Checks, Step by Step
The first question is whether the fault is in one section or across the whole unit. The technician runs each burner and each oven function to see what works and what does not. If everything is affected, the incoming supply comes next: voltage at the terminal block, gas pressure at the regulator and the condition of the connector behind the range.
If the fault is limited to one section, the testing moves into that section's parts: igniters, spark electrodes, elements, the oven sensor and the infinite switches that control burner heat on electric models. The board is tested after its inputs have been proven. The range is also checked for level and for a properly engaged anti-tip bracket, because a repair that leaves a range unsecured is not finished.
Getting a Range Out From the Wall
Most range repairs that involve the back panel, the cord, the terminal block or the gas connection mean sliding the range forward. That sounds simple, but it is where a lot of damage happens. The anti-tip bracket has to be released, the floor protected, and the range lifted slightly over the lip of the flooring rather than dragged. On a gas range, the connector has to flex without kinking, and it is checked again once the range goes back.
Electric ranges in older homes sometimes still use a three-prong cord, while newer circuits use four prongs. The technician will notice which you have and whether the cord and outlet match. Slide-in ranges sit tighter against the counters and can catch on the countertop edge, so they are eased out carefully. If your range has not moved in years, expect some dust and grease behind it; that is normal, and it is a good time to clean.
Things to Try Before the Visit
Check the breaker panel; an electric or dual-fuel range uses a double breaker that can trip partially, leaving some functions alive and others dead. Look behind the range, without moving it, to confirm the gas shutoff handle lies in line with the pipe. Dry the burner area if a spill has soaked the spark electrodes, then wait an hour before trying again.
Make sure the control lock is not engaged; on many models it is a button held down for a few seconds. Note any error codes and the model number, which is often on a label inside the oven door frame or under the storage drawer. If you smell gas, do not try any of this. Go outside, leave lights and switches alone, and reach Washington Gas or 911 from the street.
Ranges in Older Washington Homes
A lot of District kitchens still run on gas, especially in rowhouses and detached homes that have been on Washington Gas for generations. In those houses, the flexible connector between the shutoff and the range may be older than the range itself. Bare brass connectors from decades past are a recognized hazard, and even a newer one can fatigue after being flexed every time the range was shifted for cleaning or new flooring. If the technician sees an old or kinked connector, you will hear about it, and replacing it is a sensible step whether or not it caused the problem at hand.
Space matters too. Rowhouse kitchens are narrow, and a range is often wedged between a wall and a cabinet with little room to slide it out. Condo kitchens in rowhouse conversions tend to use smaller or slide-in ranges. Mention narrow doorways, steep stairs or alley-only access when you schedule; it shapes what the technician brings.
Power outages from summer storms can also confuse the electronics on newer ranges. After an outage, switch off the range breaker for a minute, then try again before assuming a part has failed.
Repair Versus Replacement for a Range
Ranges are simple machines at heart, and most of their failed parts can be replaced: igniters, elements, switches, sensors, spark modules and door hinges. A sound range with a single bad part is nearly always worth fixing. Replacement becomes reasonable when the oven cavity is rusting through, when several major parts are failing together, or when a board is no longer available.
With pro-style and high-end ranges, the case for repair is usually stronger, because the parts tend to stay available longer and replacement means more than swapping a box. The technician will explain what failed and how the rest of the range looks.
Looking After a Range
Wipe spills from the cooktop before they bake on and seep down around burners or elements. Keep the oven vent, usually under a rear burner or at the backguard, clear of pots and foil. Do not use the oven door as a step or a shelf. Every so often, check that the range still sits level and the anti-tip bracket is engaged, especially after the floor has been cleaned or the range has been moved.
On slide-in models, keep crumbs from collecting in the gap along the countertop edges, where they can scorch.
Still have questions?
Call or book online and ask us directly. We'll give you a straight answer.